Full Overview

The Poulan Pro 18-inch 42 cc 2-cycle gas anti-vibration chainsaw features a 18-inch bar. Its anti-vibration system isolates the engine from the chassis, reducing vibration and improving comfort and safety; further safety measures are ensured by the inertia-activated chain brake, which stops rotation of the chain should kickback occur. The auto oiling system lubricates the bar and chain continually during use. The saw also features: durachrome vertical cylinder design; an improved pulley starting system; a reverse sprocket for easier chain replacement; a super clean air filtration system, and a soft touch handle. The included case keeps the saw neat and clean. This unit come fully assembled and includes a 1-year warranty.

Technical Details

- Anti-vibration handle improves comfort and safety
- Includes 18-inch guide bar
- The reverse sprocket provides easy tool-less chain replacement
- Automatic oiling system lubricates the bar and chain continually during use
- Non-CARB Compliant/Not For Sale In California

Here's my review after compare the machine to the Wild Thing model....

I bought the Poulman Wild Thing saw for $149 at big box retailer. At first I thought it was OK. It did feel very light, and it seemed to start easily the first time (about 10pulls). After about 15min of use (cutting scrap highway bridge rail supports) it suddenly bogged down and died. I tried for 1/2 and hour to get again it to start to no avail. The engine's run characterstics seem to change drastically as the engine heats up. Perhaps they used too much aluminum in its construction, or perhaps the carb was mal adjusted. You cannot adjust the carb's settings so you're stuck with that. My guess is that it's a Chinese import. The pattern repeated the next day (starts, runs for a while, and dies) except that after about an hour of cool down, I finally got it to start and run for about another 5min before it died again. I contacted Poulan support, they gave some suggestions, none of them helped. Finally I returned it and upgraded to a Poulan Pro 18" 42cc for another $20 ($169). This machine is unbelievably better! I cut 5 times the wood in 1hour than I was able to cut in 3days with the "wild thing".

The Poulman Pro has many features that are better than the Wild Thing
1.) it does not leak oil everywhere when you sit it down like the wild thing
2.) Padded grips on the starter rope , not that that that matters much since it starts in 3 pulls!
3.) better chain adjustment (no tools required)
4.) heavier construction and smoother running. It's own weight is all I applied to cut through the rail posts in < 10 seconds.
5.) Cuts much better/faster than wild-thing (even though the dispacement is only 2cc more)
6.) Idles well without dying (wild-thing had to be 'petted' to keep it going, I didn't even realize that wasn't normal.)
7.) Mine came with a free extra chain! (that's almost worth the extra $20 right there)
8.) Springs between body of machine and handle to reduce vibration.

In summary, the Puolman Pro is a much better machine and gets more done, is easier to start and use and seems to use less fuel too all for $20 more. It also feels like a more solid machine and aggresively tears through wood without staggering. I'm able to completely cross cut through heavy 8" logs at 3/4 throttle, using full only occsionally as I hit knots and such. Stay away from the Wild Thing! It's a POC and sure to get you laughed at if you try to use it for any serious work!

I'm not comparing this machine to Stihl... if you are a logger or landscaper that uses chain saws as part of your livelihood, get a Stihl, but for the person that neeeds to cut a cord or 2 of wood every year, you'll be very satisfied with this machine.

I have had my poulan pro for a couple of years now, I cut about 4 to 5 cords a winter. I did have some starting troubles, but that was due to a bad plug. I love this saw, it cuts just fine. I am thinking about getting a bigger husky, some of the trees that I am cutting down I have to cut from both sides now. I am definitely going to keep this saw for a backup and around the house. I would recommend this saw to anyone, especially for the $.

I bought a Poulan because of the price. Bad idea. You do get what you pay for. After a year of light use, starting it got very hard. Once it did start, it would run for a minute or two, stall out, and then could not be started until it was fully cooled down. I took it for service at a small engine shop I know and trust. When I went to pick it up, the mechanic told me he couldn't do much with it because the carb has very limited adjustability. He said the only fix would be a new carb, which he would not recommend because of cost, and because I would probably encounter the same problem again.

I have to be honest, this is my very first chain saw, so I'm no authority on the industry standards. The saw has tackled everything I've asked of it though, so I'm confident in at least saying that it's "good".

The pull-starter system get a "F" though. I was out cutting down trees for a food plot and just like almost everyone else, the pull string didn't recoil. Being an over-confident geek though, I decided to take it apart.

After looking at it for a while, I couldn't figure out what the problem was, but when I tried to put it back together, the "EPS Spring" wouldn't fit back over the plastic post. I looked at the spring more closely and found that it had been over-torqued and now had a coil in the middle that curved inward, instead of being in alignment with the others.

So I went to [...] and clicked on "Parts and Accessories". The parts schematic labeled that spring as the "EPS Spring" (I'm certainly not versed enough to know that off the top of my head). It was $0 or so, so I bought two -- grand total about $14 and change.

I also emailed Poulan customer service, which got me a response from someone at Husqvarna, which I assume owns Poulan. The service rep was helpful and conveyed opinion that I was right about the EPS spring, but they did recommend a "kit" replacement, which I think was $11, w/o shipping. I think the kit replaces the EPS Spring, some parts, and the flat, ribbon-like spring that sits against the wall/plastic. I passed on the kit.

The EPS springs arrived today, and while I haven't installed them yet, I'm ------ scratch that, I just went downstairs and installed one of my new EPS springs. Problem is solved!!!

It's really a piece of cake. There are 4 screws on the outside that hold the pull starter assembly onto the saw. There there is one screw that holds a plastic gear onto a post of the outer housing. Just remove that screw in the middle of the plastic gear and the EPS spring sits right there underneath the plastic gear. You don't have to mess with the the pull string or anything.

One thing to note, Husqvarna/Poulan customer support did recommend that I take the saw to an authorized dealer, as the saw has a 2 year warranty that YOU WILL VOID IF YOU OPEN UP THE SAW. Of course, I don't know how they would be able to tell that because I didn't notice any tamper evident tape on it -- but you've been warned!!!!

For me personally, $14 (which gives me an extra spring if this happens again) makes a lot more sense than wasting my time dropping off and picking up the saw at a service center.

2 friends recommended this brand so i gave it a shot. I've waited over a year to give it a review so that i could be as accurate as possible. Out of the box it was hard to start, pullrope kept hanging up (out) and i had to either smack it on something or take it apart to get it to go back in.
Beside the pullrope issue it is extremely difficult to start once it gets warmed up. It pumps way too much oil for the bar/chain (which in some respect is better than too little) and drips the rest while not in use. Anti-vibration is a joke, i feel the vibration worse with this saw than any other saw i've owned/used. The idea of the chain adjustment actually being in the bar sounds great but its a real failure. It is either too tight or too loose, no in between. Replacement bar is more expensive than normal. After having to replace the clutch, bar and chain due to a combination of abuse and poor quality, i bought an ECHO brand chainsaw. The 16 inch ECHO works like a champ (again over a year old) and puts the Poulan to shame. I work on the Poulan 70% of the time and get 30% use from it. I work on the ECHO 5% of the time and get 95% use from it. Something you should also keep in mind..POULAN,CRAFTSMAN,HUSQVARNA..same saw in different clothing, all products of ELECTROLUX. Word

I purchased the saw because of price and once again got burned.
After 2 months the saw became very hard to start. I brought the saw into a dealer, who indicated that it needed carburator work. The saw has been there for over 3 months now. I had to buy another saw to get my work done, while waiting for this one to be fixed.
I called Poulan and they are not helpful at all. They just tell me that it should be fixed soon. I thought that after all this time, that if the saw can't be fixed, it should be replaced. But they didn't see the wisdom in that line of thought.
All I can say is buyer beware!!

Poulan Pro 42 CC 18 in bar.
The good, inexpensive, comes with a case, and an extra chain. Best of all, based on the prior reviews I bought the extended warranty - full replacement.
The bad, That's the problem. Start with power. Sure this is a 42 CC motor, you should expect some power. But according to my seat of the pants usage, the saw is far too underpowered for even a 16" bar. It would probably have enough power for a 12 inch bar. To prove this case, I contacted Poulan who told me the saw has 1 HP per 29 CC, based on that calculation the saw has approximately HP. Based on my experience, that is right in line with the performance seen with this saw. You simply can't compare CC to CC when looking at a budget saw vs. a real chain saw. A 40 CC motor from Husqvarna produces around 2.4 HP.
Automatic Chain Tension - This is an absolute engineering disaster. After some usage, my saw would not keep the chain tight. After an adjustment and a couple cuts of 6" limb or 1 cut of 12" or bigger, and I would need to readjust the chain tension. Upon calling Poulan, they sent me a replacement part. The revised part removed the tool less chain adjustment returning the saw to a typical chain adjustment with two nuts, and the adjustment screw.
Extra Chain - It is a good thing the saw came with the extra chain. During the second tree cut down with this saw, the chain became so loose on a 14" log that it tossed the chain bending a fair number of the chain guides. The chain was relatively destroyed.
It comes with a nice case.
My suggestions, DO NOT BUY this saw. If price is really a factor (as it was for me) do yourself a favor, spend a little more money, and get a small saw from Echo, Husqvarna, Stihl, or any other producer of a real chain saw. Don't worry about CC's or the bar, these other saws will be lighter, more powerful and easier to use. If you really want an 18" bar, purchase an aftermarket bar & chain from Oregon. You will be much happier and the money will be well spent. Sure a small saw with the 18" bar would be under powered, but it will be much less underpowered than that 42CC Poulan.
Prior to buying this saw, I found it hard to justify buying a good saw. I don't need a saw very often. Now, even though I rarely need a saw, I will be purchasing one by Echo, Husqvarna, or Stihl in the 40-50 cc range. You can't put a price on frustration.

I decided to step up to a larger "Pro" chainsaw because my trusty 18 year-old Homelite 14" saw is a little small for some bigger trees. It still runs great, so I decided to keep it as a backup unit. Turned out to be a REALLY good idea.

I took the 18" Poulan Pro to my ranch to cut some trees and the starter cord pulled out and would not retract so I could start the saw. The housing is screwed on in a million places with funky torx screws (they obviously don't want you in there) so I could not spin the hub to respool the cord. I finally found a pen and shoved it throught the slots in the housing and retracted the starter cord. It pulled out again and would not retract. Re-spool, cuss, repeat. No go. 75 miles from the nearest town, and this thing was useless. Glad I had the backup.

I got back to town and took the unit back to the retail store and exchanged it, figuring I must have gotten the one bad unit. Wrong! I drove home with the replacement and opened the box. You guessed it, the cord was pulled out and you could see that the previous customer had the same problem I did- the starter cord would not retract. The retailer just put it back in stock. I got my money back and looked to see if there was another unit (that I could open and try in the store). There was one up in the rack, with a DNI (do not inventory) sticker on it, and it was in pieces. Third bad unit. The cheaper "Wild Thing" display model was torn apart on the display shelf as well. The cowling was off, so I assume that the starter cord was stuck on it, too.

So, three Poulan Pro 18" units with stuck starter cords, and one Wild Thing torn apart. Not a ringing endorsement for Poulan quality.

I recommend finding another chain saw unless you like cutting wood without the engine running.

Got a reconditioned 16" Poulan 12 years ago. Made a lot of sculptures, cut down a lot of trees; died of abuse . Got a reconditioned P.Pro 18" anti-shaker last week from the Outdoor Store for 100bucks. Cut down 5- 40 foot tall trees with a breeze this week. The old saw didn't have an emergency brake( new one does ), I was hitting it unintentionally causing it to stall, sent an email to the Outdoor Store; response quick and helpful.

I did quite a bit of cutting last fall, and it worked well. The tensioning lock system is pathetic, but Poulan will provide you with the original double nut system free of charge, which I highly recommend.

These are equipped with the current anti-pollution mixture adjustment screws, which take a special tool not authorized for the public. You can, however obtain them on e-bay; and unless you're up for periodically toting the saw to a repair shop, and shelling out $20 or more for a minor adjustment, I suggest getting one.